Original price was: $449.88.Current price is: $369.98.

8pc Black Oxide HSS Silver & Deming set, 1-1/16″ to 1-1/2″.

118-degree split point, 1/2″ cut down shank for any 1/2″ chuck, 6″ overall, 3″ flute.

Family Owned. Slightly Twisted.

Real people who actually know drill bits pick up the phone.

Fast Shipping Nationwide

Most orders are out the door the same or next business day.

Built for Steel, Not Shelves

Shop-grade bits for people who drill all day and break stuff for a living.

Stumped? Call the Bit Experts.

Tell us the material and the job, and we'll get you the right bit. 800-350-8665.

8Pc Black Oxide S&D JUMBO Drill Set, 1-1/16″ to 1-1/2″

The Jumbo 8piece S&D Drill Set is our 1-1/16″ to 1-1/2″ Monster Drill Set, covering eight sizes in 1/16″ steps. These are the biggest diameter drills you can buy. Each drill is Top Quality High Speed steel with a Black Oxide finish and a 1/2″ Cut Down shank, so you can use them in any 1/2″ drill chuck hand drill or drill press.

Jobber Length, 118-Degree Split Point. All drills come in a 6″ Overall length with a 3″ Flute length. These drills are great for general purpose drilling in metal, pipe, wood, composites, plastics, and most materials.

Applications

  • Large holes in steel plate, pipe and structural steel
  • Conduit, pipe and fitting holes in panels and brackets
  • Wood, composites and plastics
  • Drill press or 1/2″ hand drill work in fabrication, maintenance and farm shops

Specifications

Pieces 8
Size Range 1-1/16″ to 1-1/2″ (by 1/16″)
Material High Speed Steel (HSS)
Finish Black Oxide
Length Jobber
Point 118-Degree Split Point
Shank 1/2″ Cut Down
Overall Length 6″
Flute Length 3″
Fits Any 1/2″ drill chuck, hand drill or drill press

Set Includes

Fraction Decimal Metric
1-1/16″ 1.0625″ 26.99 mm
1-1/8″ 1.1250″ 28.58 mm
1-3/16″ 1.1875″ 30.16 mm
1-1/4″ 1.2500″ 31.75 mm
1-5/16″ 1.3125″ 33.34 mm
1-3/8″ 1.3750″ 34.93 mm
1-7/16″ 1.4375″ 36.51 mm
1-1/2″ 1.5000″ 38.10 mm

Recommended Starting RPM

These are starting points. Lower the speed if the drill chatters, squeals or the chips turn blue. Raise it gradually in soft materials if the cut is clean.

Size Mild Steel Stainless Cast Iron Aluminum Wood / Plastic
1-1/16″ 290 145 250 720 540
1-1/8″ 270 135 240 680 510
1-3/16″ 255 130 225 645 485
1-1/4″ 245 120 215 610 460
1-5/16″ 235 115 205 580 435
1-3/8″ 220 110 195 555 415
1-7/16″ 215 105 185 530 400
1-1/2″ 205 100 180 510 380

What Black Oxide Does

Black oxide is a conversion coating on the steel surface. It adds mild corrosion resistance and helps hold cutting oil on the drill, which reduces friction and chip welding compared to a bright (uncoated) finish. It does not change the drill’s size.

S&D Drill vs. Hole Saw vs. Step Bit vs. Annular Cutter

Tool Best For Limits
S&D drill Round, true holes in thick or solid material: plate, bar, pipe walls, wood beams. Fits a standard 1/2″ chuck. Removes all material as chips, so it needs more torque and a pilot hole in metal.
Hole saw Fast holes in thin sheet, wood and drywall. Limited cutting depth, rougher hole, slugs can bind in the cup.
Step bit Thin sheet metal and panels, multiple sizes with one bit. Only works in thin material, roughly the height of each step.
Annular cutter Production holes in thick steel on a mag drill. Needs a mag drill or arbor setup and a higher cost per size.

Drilling Tips

  • Pilot hole: In metal, drill a pilot of about 1/4″ to 3/8″. For the biggest sizes in thick steel, step up through an intermediate size such as 5/8″ or 3/4″.
  • Drill press preferred: A drill press gives you low speeds, steady feed and a straight hole. Clamp the work. Never hold it by hand.
  • Hand drill use: Use a 1/2″ drill with low gearing and a side handle. Brace for kickback, because a 1-1/2″ drill can grab hard, especially at breakthrough.
  • Low RPM, steady feed: The bigger the bit, the slower the speed. Keep a steady feed so the edges cut instead of rubbing.
  • Breakthrough: Ease off the feed as the point exits. This is where large drills catch thin stock and pipe.
  • Cutting fluid: Use cutting oil in steel and stainless and a light lubricant in aluminum. Drill cast iron and wood dry or with light lubricant.
  • Clear chips: Back out periodically in deep holes to clear the flutes.

FAQ

What sizes are in the 8Pc S&D JUMBO Drill Set?

1-1/16″, 1-1/8″, 1-3/16″, 1-1/4″, 1-5/16″, 1-3/8″, 1-7/16″ and 1-1/2″.

Will these fit my 1/2″ drill?

Yes. Every drill has a 1/2″ cut down shank, so you can use them in any 1/2″ drill chuck hand drill or drill press.

What RPM should I run a 1-1/2″ drill in steel?

A good starting point is about 200 RPM in mild steel and about 100 RPM in stainless, with cutting oil.

Do I need a pilot hole?

In metal, yes. A 1/4″ to 3/8″ pilot reduces the feed force and helps the drill start on center.

How deep can these drills cut?

Each drill has a 3″ flute length on a 6″ overall length.

What materials can they drill?

They’re great for general purpose drilling in metal, pipe, wood, composites, plastics, and most materials.

Additional information

Weight 9 lbs
Dimensions 8 × 4 × 8 in

Need help choosing the right product?

Our product team can help you compare sizes, shanks, and applications before you order.

You may also like

High Speed Silver and Deming Drill Bit
-61%

Price range: $13.88 through $133.77

Cobalt Step Drill Bit for hardened steel
-30%

Price range: $42.12 through $79.98